home-assistant.io/source/_integrations/airobot.markdown

title, description, ha_release, ha_iot_class, ha_codeowners, ha_domain, ha_integration_type, ha_dhcp, ha_config_flow, ha_quality_scale, ha_category, ha_platforms

title	description	ha_release	ha_iot_class	ha_codeowners	ha_domain	ha_integration_type	ha_dhcp	ha_config_flow	ha_quality_scale	ha_category	ha_platforms
Airobot	Instructions on how to integrate Airobot smart thermostats for intelligent floor heating control into Home Assistant.	2025.12	Local Polling	@mettolen	airobot	device	true	true	bronze		climate

The Airobot {% term integration %} allows you to control and monitor Airobot smart thermostats for intelligent floor heating control via the local REST API. The thermostat uses adaptive learning with a TPI algorithm to maintain stable temperatures and optimize energy efficiency. Optional built-in CO₂ and humidity sensors monitor indoor air quality for a healthier living environment.

Supported devices

The following devices are supported by the integration:

• Airobot Smart Thermostat TE1 with firmware version 1.8 or later

Prerequisites

Before setting up the integration, ensure your Airobot thermostat is properly configured:

1. Verify your thermostat has firmware version 1.8 or later. You can check the firmware version in the thermostat settings menu.
2. Connect the thermostat to your local WiFi or Ethernet network.
3. Connect to the internet at least once to register with the Airobot server. During this initial connection, the thermostat receives its Device ID (username) and password.
4. In the thermostat settings menu, navigate to Connectivity > Local API > Enable to enable the local REST API (disabled by default).
5. Note your Device ID and password from the thermostat menu under Connectivity > Mobile app screen. You will need these during setup. These are the same credentials used to pair the mobile app.

After initial setup, the thermostat does not require internet connectivity to function with Home Assistant.

{% include integrations/config_flow.md %}

The integration can be automatically discovered via DHCP when the thermostat is on the same network. If automatic discovery does not work, you can manually add the integration.

{% configuration_basic %} Host: description: "The hostname or IP address of your Airobot thermostat. You can find it in your router settings, or use the hostname format airobot-thermostat-t01xxxxxx (replace t01xxxxxx with your Device ID in lowercase)." Username: description: "The thermostat Device ID (e.g., T01XXXXXX). You can find this in the thermostat menu under Connectivity > Mobile app screen. This is the same credential used to pair the mobile app." Password: description: "The thermostat password. You can find this in the thermostat menu under Connectivity > Mobile app screen. This is the same credential used to pair the mobile app." {% endconfiguration_basic %}

Supported functionality

The Airobot integration provides climate control functionality with comprehensive temperature management and preset modes.

Climate

The thermostat is represented as a climate entity with the following capabilities:

• Current temperature: Displays the measured temperature in the room.
  • If a floor temperature sensor is connected, displays the floor temperature (for floor heating control).
  • Otherwise, displays the air temperature.
• Current humidity: Displays the measured relative humidity in the room.
• Target temperature: Shows and allows you to set the desired temperature (5-35°C range).
  • In HOME mode: Controls the HOME temperature setpoint.
  • In AWAY mode: Controls the AWAY temperature setpoint.
• HVAC mode: Always set to Heat for this heating-only thermostat.
• HVAC action: Shows whether the thermostat is actively heating or idle.
• Preset modes:
  • Home: Use the HOME temperature setpoint
  • Away: Use the AWAY temperature setpoint (typically lower for energy savings)
  • Boost: Temporarily boost heating for 1 hour, then return to the previous mode

Data updates

The Airobot integration {% term polling polls %} data from the thermostat every 30 seconds. This interval matches the thermostat's internal measurement cycle, ensuring efficient data synchronization without overwhelming the device.

Troubleshooting

Cannot connect to thermostat

Symptom: "Cannot connect to your Airobot thermostat"

When trying to set up the integration, the configuration flow shows the error "Cannot connect to your Airobot thermostat".

Description

This error indicates that Home Assistant cannot establish a connection to the thermostat's local REST API. This can be caused by incorrect network settings, local API being disabled, or network connectivity issues.

Resolution

To resolve this issue, try the following steps:

1. Verify the IP address or hostname:

   • Make sure you entered the correct IP address or hostname.
   • You can find the IP address in your router settings.
   • The hostname format is airobot-thermostat-t01xxxxxx (replace t01xxxxxx with your Device ID in lowercase).

2. Check network connectivity:

   • Ensure the thermostat is powered on and connected to your network.
   • Verify that Home Assistant and the thermostat are on the same network or can communicate with each other.
   • Try pinging the thermostat from the Home Assistant host: ping <thermostat-ip>.

3. Enable local API:

   • On the thermostat, navigate to Connectivity > Local API > Enable.
   • Wait a few seconds for the API to become active.

4. Restart the thermostat (if needed):

   • If the local API was just enabled, try restarting the thermostat to ensure the API service starts properly.

Authentication failed

Symptom: "Invalid authentication"

The configuration flow shows "Invalid authentication" error when entering credentials.

Description

The Device ID (username) or password provided is incorrect or does not match the thermostat's credentials.

Resolution

1. Verify credentials:

   • On the thermostat, navigate to the Connectivity > Mobile app screen in the settings menu.
   • Check that the Device ID (e.g., T01XXXXXX) matches exactly what you entered (case-sensitive).
   • Check that the password matches exactly what you entered (case-sensitive).

2. Re-enter credentials:

   • Double-check for typing errors.
   • The Device ID should start with "T" followed by numbers.

3. Ensure initial registration:

   • The thermostat must have connected to the internet at least once to register and obtain credentials.
   • If you have never connected the thermostat to the internet, do so first, then check the credentials again.

Thermostat goes unavailable

Symptom: The thermostat entity becomes unavailable after some time

Description

The integration loses connection to the thermostat, causing the entity to become unavailable. This can happen due to network issues, thermostat power loss, or the device entering sleep mode.

Resolution

1. Check power and network:

   • Ensure the thermostat is powered on and connected to the network.
   • Check if you can access the thermostat's web interface directly in a browser.

2. Verify network stability:

   • Check for WiFi signal strength issues if using wireless connection.
   • Consider using a wired Ethernet connection for more reliable connectivity.

3. Check local API status:

   • Ensure the local API is still enabled on the thermostat.
   • Navigate to Connectivity > Local API and verify it is enabled.

Removing the integration

This integration follows standard integration removal. No extra steps are required.

{% include integrations/remove_device_service.md %}

You can optionally disable the local API on the thermostat after removing the integration by navigating to Connectivity > Local API > Disable.